A. Telnet

B. FTP

C. Console connection

D. AUX connection
 
13: You want to prevent unauthorized users from plugging their laptops into the router. What type of password helps prevent this issue?

A. vty

B. Interface

C. Console

D. Enable
 
14: You have connected to the console port and are running HyperTerminal. You see only scrambled characters and symbols. What is the most likely solution to this problem?

A. Change the connectors.

B. Use a different Terminal program.

C. Reset the router.

D. Adjust the baud rate of your COM port.

[View full size image]
 
 
15: Which of the following commands would you type to receive this output shown in the figure above?

A. Show running-config

B. Show startup-config

C. Show ip route

D. Show version
 
16: You are configuring a router named East for authentication with a router named West using CHAP. What username should you configure on East to allow the routers to communicate?

A. East

B. West

C. South

D. North
 
17: What is the default point-to-point encapsulation protocol used on a Cisco router?

A. PPP

B. SLIP

C. HDLC

D. ATM
 
18: What type of handshake occurs with CHAP authentication?

A. One-way

B. Two-way

C. Three-way

D. Mutual
 
19: You have connected to your Cisco router through a Telnet connection. To test one of your connections, you use a debug ip packet command. Even though you are sure traffic is passing through your router, nothing is reported in your terminal window. What is the most likely cause of this problem?

A. There is no debug ip packet command.

B. You need to type in the terminal monitor command to see debug output from a Telnet session.

C. This command displays information only if the interface experiences trouble. No output indicates that the interface is fine.

D. Cisco routers do not allow you to enable debug commands remotely due to security restrictions.

[View full size image]
 
 
20: Which of the following commands would you type to see this output on your Cisco router shown in the previous figure?

A. Show version

B. Show running-config

C. Show startup-config

D. Show router setup

21: Which of the following commands would you type to see this output shown in the figure above?

A. Show interface Ethernet 0/0

B. Show ip interface detail

C. Show interface Serial 0/1

D. Show ip interface brief

22: Your routers at ACME, Inc., are having some connectivity issues. You issue show commands for each connecting router's interface. Why are they unable to communicate (see figures above)?

A. Incorrect IP address

B. Wrong routing protocol

C. Bad cable

D. Encapsulation mismatch
 
23: You need to back up the configurations you just made, but no TFTP servers are available. Which of the following commands are options to back up your currently running configuration? (Choose two.)

A. Router1#copy running-config startup-config

B. Router1#copy running-config flash

C. Router1#copy startup-config running-config

D. Router1#copy running-config http
 
24: You are consulting a small business that is establishing its first WAN link. The client wants to know what encapsulation you will be using on the link. Which of the following are valid encapsulations for WAN links? (Choose three.)

A. Frame relay

B. Ethernet

C. Token ring

D. PPP

E. HDLC
 
25: Your boss is concerned about security on your network. She wants to make sure that no one can identify passwords if he or she happens to view a configuration on your router. What command encrypts all passwords on your router?

A. Router1#service password-encryption

B. Router1(config)#service password-encryption

C. Router1#enable secret password

D. Router1(config)#enable secret password
 
26: You need to set up a password that will prevent unauthorized users from telnetting into your router. What series of commands would you use?

A. Acme1(config)# line console 0
   Acme1(config-line)# password acme
   Acme1(config-line)# login

 B. Acme1(config)# line vty 0
   Acme1(config-line)# enable password acme

 C. Acme1(config)# line vty 0
   Acme1(config-line)# enable secret acme
   Acme1(config-line)# login

 D. Acme1(config)# line vty 0
   Acme1(config-line)# password acme
   Acme1(config-line)# login

27: When you are setting up your serial interfaces, what does the clockrate command do for your connection?

A. Establishes the timing at which you send data

B. Establishes keepalives

C. Establishes the advertised bandwidth

D. Establishes the time on the router
 
28: You need to set up passwords on all your default Telnet lines. What command would you start with?

A. Router1(config)#telnet configuration

B. Router1(config)#interface Ethernet 0/1

C. Router1(config)#line vty 1 5

D. Router1(config)#line vty 0 4
 
29: You can execute show commands at which prompt? (Choose two.)

A. Router1#

B. Router1(config)#

C. Router1(config-router)#

D. Router1>

E. romon1>
 
30: You are configuring your router and type in an Enable password and an Enable Secret password. Your fellow network technician asks you why you have two passwords set when you need only one. What do you tell him?

A. The Enable password is used by low-level applications.

B. If you reverted to an older version of the IOS, it would not understand the Secret password.

C. Both passwords are treated the same.

D. It is a failsafe method of ensuring that people need to type two passwords instead of just one.

31: You need to get back to Privileged EXEC mode from Interface Configuration mode. What is the quickest method?

A. Ctrl+Shift+6; then press X

B. Ctrl+Esc

C. Ctrl+Z

D. Type exit
 
32: When you are establishing a PPP link, which of the following would be negotiated? (Choose three.)

A. IPCP

B. CHAP

C. UDP

D. Q.931

E. Multilink Protocol
 
33: Which of the following commands returns your router to a previously saved configuration?

A. Router1#setup

B. Router1#copy running-config startup-config

C. Router1#copy startup-config running-config

D. Router1#reload
 
34: You are in Interface Configuration mode and would like to recall the last command you typed, move your cursor to the beginning of the command line, and type no before the recalled command. You notice your up- and down-arrow keys do not function because you are using an older terminal program. What command combinations could you use to recall the previous command and move your cursor to the beginning of the line?

Press Ctrl+P to recall the previous command and Ctrl+A to move to the beginning of the command line.

Press Ctrl+L to recall the previous command and Ctrl+B to move to the beginning of the command line.

Press Ctrl+D to recall the previous command and Ctrl+A to move to the beginning of the command line.

Press Ctrl+E to recall the previous command and Ctrl+A to move to the beginning of the command line.
 
35: What is the baud rate setting for your terminal emulation program so that you can communicate through your console port?

A. 2400

B. 9600

C. 14400

D. 36300
 
36: What must be configured on a Cisco device to enable Telnet functionality?

A. A management IP address

B. SNMP

C. CDP

D. vty ports
 
37: You are configuring your Cisco router and need to go back to User EXEC mode. What command takes you back to User EXEC mode?

A. Router1#enable

B. Router1#exit

C. Router1#configure terminal

D. Router1#disable
 
38: Which of the following commands places an IP address on your Catalyst switch?

A. Switch1#ip address 10.2.2.2 255.255.255.0

B. Switch1(config)#Set IP 10.2.2.2 255.255.255.0

C. Switch1(config-vlan)#ip address 10.2.2.2

D. Switch1(config-vlan)#ip address 10.2.2.2 255.255.255.0

39: Which of the following commands would you enter to receive this output shown in the figure above?

A. Router1#show NVRAM

B. Router1#show Flash

C. Router1#show Flash-Mem

D. Router1#show Version